Siding & Exterior Painting in Chisholm Valley West, Round Rock, TX

How did this Chisholm Valley West project take shape?

The homeowner found us through an online search and reached out on July 2, 2025, about the home's exterior. We inspected the property and began the estimate on July 7. The plan grew beyond new boards: it covered the surfaces that meet the siding, including garage-door jambs and painted trim. The homeowner approved the project on September 3, well before the installation crew arrived.

That wider scope matters on homes across Round Rock. A siding job can look unfinished if the boards are new but the garage surrounds and nearby painted surfaces remain untouched. Here, the approved work included both trades, so we could address those transitions during one on-site window. We did not treat the paint as an unrelated job to tackle later.

Why use Select Cedar Mill fiber cement here?

We chose 8.25-inch Select Cedar Mill fiber cement siding for its defined board width and cedar-textured face. It gives this Round Rock home a wood-grain look without making the exterior out of wood boards. Central Texas summers can push past 100°F, so material choice deserves more thought than color alone. The plan also called for 7/16-inch OSB sheathing, which kept the surface behind the siding in the installation scope. New cladding should not be considered in isolation from what supports it.

The boards arrived primed for the paint portion of the job. That distinction is easy to miss: primed siding is not the same as siding that has received its specified finish coat. We paired the selected James Hardie profile with SuperPaint rather than leaving the primed surface as the final appearance. The textured face remained visible beneath the paint.

What needed attention around the garage openings?

The garage area had more detail than a straight run of siding. Our scope called for a split double garage-door jamb wrap, noted as two single openings, plus another garage-door jamb wrap. Those surrounds deserved their own line in the plan because a broad siding board cannot finish a narrow jamb by itself.

• The split-double detail covered two individual garage-door openings, not one continuous opening.
• A separate jamb-wrap item addressed another garage transition in the siding scope.
• Material delivery was included so the boards, sheathing, and finishing work could be coordinated on site.
• The garage doors themselves were part of the painting scope, not a garage-door replacement.

Details like these are where an exterior can look pieced together. At the garage, the viewer sees the siding, jambs, and doors at once. Accounting for each surface helped us carry the finish across that busy part of the home without suggesting that a new door was installed.

What did the exterior painting include?

The paint work went past the siding. We used Sherwin Williams SuperPaint for the exterior finish and included the fascia, soffit, and garage doors in the painting scope. Painting those surfaces during the siding project let the crew address the edges homeowners notice from the street and driveway.

• The fascia and soffit painting scope extended to surfaces up to 24 inches.
• The new siding received paint after installation rather than remaining in its primed state.
• Garage-door painting was listed separately from the jamb-wrap work.
• The painting scope also allowed for other measured exterior surfaces without claiming a whole-house repaint.

For a home exposed to Central Texas sun, the practical question is which surfaces a paint plan actually covers. A fresh coat on the boards alone would not include the fascia or the garage doors. Here, those areas were named in the work, making the boundary of the paint job much clearer.

How did we handle the installation window?

The crew worked from Friday, October 31, through Monday, November 3. This was a four-day on-site project, not a same-day siding changeout. The work combined sheathing, fiber cement installation, garage-jamb details, and exterior painting; the available dates do not assign each task to a particular day.

• Siding materials included primed Select Cedar Mill boards in the specified 8.25-inch profile.
• The garage scope required both the two-single-opening wrap and an additional jamb wrap.
• Painting covered trade-specific surfaces as well as the new siding.
• The final work included punch items and two yard cleanups.

Keeping those tasks together gave us a sensible way to finish the exterior. It also avoided treating cleanup as an afterthought once the paint was on. By the last on-site day, the crew had finished its remaining punch work and cleared the work areas.

What was different when the crew finished?

On November 3, the home had a newly clad exterior paired with painted garage and trim surfaces. The Select Cedar Mill texture added definition to the siding, while the paint brought the separate work areas into a consistent appearance. The finished scope is specific: siding and exterior paint, including the named garage and fascia details.

• The siding choice supplied a cedar-mill texture in fiber cement rather than natural cedar.
• The garage surrounds received trim attention alongside the broad wall surfaces.
• Fascia and soffit were included in the visible paint finish.
• The completed work remained within the approved siding and exterior painting trades.